PHR www.vishay.com vishay sfernice revision: 28-aug-15 1 document number: 53037 for technical questions, contact: sferthinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 escc ( ) 4001/023 qualified high precision (5 ppm, 0.01 %), thin film chip resistors vishay sfernice thin film division holds escc qml qualification (escc technology flow qualification). these high-rel. components are ideal for low noise and precision applications, superi or stability, low temperature coefficient of resistance, and low voltage coefficient, vishay sfernices precision thin film wraparound resistors exceed requirements of mil-prf-55342g characteristics y ( 10 ppm/c). features ? load life stability at 70 c for 2000 h: ? 0.15 % under pn ? low temperature coefficient down to 5 ppm/c ? very low noise (< -35 db) and voltage coefficient ? (< 0.01 ppm/v) ? resistance range: 10 ? to 3 m ? (depending on size) ? laser trimmed tolerances to 0.01 % ? tcr in lot tracking ? 5 ppm/c ? termination: thin film technology ? snpb terminations over nickel barrier ? escc 4001 (generic specifications) ? escc 4001/023 (detailed specifications) ? escc qualified ? smd wraparound chip resistor ? operating temperature ra nge: -65 c to +155 c ? from 0402 to 2010 ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 note (1) limiting voltages and power rating are already derate d (for maximum ratings admissible, refer to p chip: www.vishay.com/cod?53017 ). note (2) for b terminations use recommended reflow profile #1 as per application note gui delines for vishay sfernice resistive and inductive components (document number: 52029) standard electrical specifications model size escc variant number resistance range ? rated power at + 70 c (pn) w (1) limiting element voltage (ul) v (1) insulation voltage ( u i ) v tolerance % temperature coefficient ppm/c PHR 0402 0402 13 and 14 10 to 150k 0.05 30 50 0.01, 0.02, 0.05, 0.1 5, 10, 25 PHR 0603 0603 01 and 05 10 to 500k 0.1 35 100 0.01, 0.02, 0.05, 0.1 5, 10, 25 PHR 0805 0805 02 and 06 10 to 750k 0.125 75 200 0.01, 0.02, 0.05, 0.1 5, 10, 25 PHR 1206 1206 03 and 07 10 to 3.5m 0.25 100 300 0.01, 0.02, 0.05, 0.1 5, 10, 25 PHR 2010 2010 04 and 08 10 to 6m 0.50 150 300 0.01, 0.02, 0.05, 0.1 5, 10, 25 climatic specifications operating temperature ? range -65 c; +155 c soldering temperature ? (t sol ) 260 c, immersion 10 s mechanical specifications substrate material alumina technology thin film film nickel chromium with mineral ? passivation protection epoxy and silicone terminations b type: snpb over nickel barrier ? for solder reflow (3) ? g type: gold
PHR www.vishay.com vishay sfernice revision: 28-aug-15 2 document number: 53037 for technical questions, contact: sferthinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 traceability definitions the two major traceability elements are defined as: ? the primary process lot number named front end lot (fe lot). one fe lot is composed of several wafers issued from the same thin film deposition sequence. ? the date code named batch nu mber (bn). the bn is defined after completio n of the end of production testing sequence. the lot homogeneity is given by the fe lot and not by the bn. according to the applied rules validated by the escc through the product qualification, the following situations are agreed: ? parts coming from different fe lost might have the same bn. ? a maximum of two different bn might be applied to the same fe lot to enable the use of overruns from a previous po. ? unless requested / approved by the custom er the bn will be 2 years old maximum. specific traceability requirements the following specific requirements have to be treated as: ? a customer who requires lot homogeneity has to mention it on the po as single production lot. ? a customer who requires lot homogeneity in addition to a single batch number has to mention it on the po as single production lot and option r0101. end of production testing mandatory testing performed at th e end of the production process: ? 100 % overload: voltage or 2 ul whichever is less - duration 2 s ? 100 % burn in: 168 h at pn at 70 c options lot validation testing for procurement of qualified components, lo t validation testing is not required and shall only be perfo rmed if specifically stipulated in the purchase order. for procurement of unqualified co mponents, lot validation testing shall be performed as stipulated in the purchase order. the need for lot validation testing sha ll be determined by the orderer. when lot validation testing is required, it shall consist of the performance of one or more of the tests or subgroup test seque nces of chart f4 indicated in the esa generic specification escc 4001. the testing to be performed an d the sample size shall be as stipulated in the purchase order. when procurement of more than one component type is involved from a family, range or series, the selection of representative samples shall also be stipulated in the purchase order. lot validation testing will be composed of one lvt charges and lvt samples: ? lot validation test charges has to be ordered separately on purchase order. ? lot validation samples have to be or dered separately on purchase orderer. final inspection if requested by the orderer a final in spection can be performed on site. ? final inspection has to be stipul ated separately on purchase order. dimensions in millimeters variant ? number style dimensions abcde min. max. min. max. min. max. min. max. min. max. 01, 05 0603 1.39 2.16 0.62 1.01 0.25 1.02 0.17 0.51 0.25 0.51 02, 06 0805 1.78 2.55 1.14 1.53 0.25 1.02 0.17 0.51 0.25 0.51 03, 07 1206 2.87 3.64 1.47 1.86 0.25 1.02 0.17 0.51 0.25 0.51 04, 08 2010 4.95 5.72 2.41 2.8 0.25 1.02 0.35 0.85 0.35 0.85 13, 14 0402 0.87 1.64 0.47 0.86 0.25 1.02 0.09 0.38 0.12 0.38 a d d c e e b 6.25 pn x rn ??
PHR www.vishay.com vishay sfernice revision: 28-aug-15 3 document number: 53037 for technical questions, contact: sferthinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? suggested land pattern: according to ipc-7351a note (1) for values, tcr, tolerance outside of qualified range: please consult. popular options option 0041 production according to escc 4001/023 for: cases, ohmic values, tolerance or tcr outside of qualified range. ? please consult vishay sfernice for feasibility. note (2) moq: 50 pieces extended features you may consult vishay sferni ce for chip sizes, ohmic values and tolerances outs ide of the qualified range. power derating curve land pattern in millimeters chip size z max. g min. x max. 0402 1.55 0.15 0.73 0603 2.37 0.35 0.98 0705/0805 2.76 0.74 1.40 1206 3.91 1.85 1.73 2010 5.93 3.71 2.67 g min. z max. x max. qualified ohmic range (1) model escc variant ohmic range ( ? ) tolerance (%) PHR 01 to 08 and 13 to 14 10 to < 50 0.1 50 to < 100 0.05 and 0.1 100 to < 250 0.02, 0.05 and 0.1 ? 250 0.01, 0.02, 0.05 and 0.1 qualified ohmic range (1) model escc variant ohmic range ( ? ) temperature coefficient (ppm/c) escc code PHR 01 to 08 and 13 to 14 10 to < 20 e: 25 (-55 c; +155 c) 2 20 to < 50 e : 25 (-55 c ; +155 c) y : 10 (-55 c ; +155 c) z : 5 (+22 c ; +70 c) 2 1 0 ? 50 e : 25 (-55 c ; +155 c) y : 10 (-55 c ; +155 c) z : 5 (+22 c ; +70 c) c : 5 (-55 c ; +155 c) 2 1 0 9 qualified ohmic range: max. value (1) PHR 0402 PHR 0603 PHR 0805 PHR 1206 PHR 2010 100 k ? (67 k ? for tcr c) 200 k ? (160 k ? for tcr c) 250 k ? 1 m ? 3 m ? packaging two types of packaging are available: waffle-pack and tape and reel. size number of pieces per package tape width waffle pack 2" 2" tape and reel (3) min. max. 0402 100 50 5000 8 mm 0603 0805 4000 1206 140 2010 60 2000 0 1206 ambient temperature in c rated power 070 155 0603 0805 2010 500 250 125 100 50 0402
PHR www.vishay.com vishay sfernice revision: 28-aug-15 4 document number: 53037 for technical questions, contact: sferthinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 performance test conditions requirements typical esa/scc 4001/023 mil-prf-55342g short time overload u max. < 2 ul - 2 s 0.05 % + (0.05 ? x 100/rn) 0.10 % 0.01 % rapid temperature ? change -55 c / +155 c 5 cycles cei 66-2-14 test na 0.05 % + (0.05 ? x 100/rn) 0.1 % (for 100 cycles) 0.01 % 0.015 % (for 500 cycles) soldering ? (thermal shock) 260 c / 10 s cei 68-2-20 a test t6 (met. 1a) 0.05 % + (0.05 ? x 100/rn) - 0.005 % terminal strength: ? adhesion bend strength ? of end plated facing cei 115-1 clause 4.32 cei 115-1 clause 4.33 0.05 % + (0.05 ? x 100/rn) - 0.01 % climatic sequence cei 67-2-1 / cei 68-2-2 cei 67-2-13 / cei 68-2-30 0.10 % + (0.05 ? x 100/rn) - 0.02 % insulation resistance > 1 g ? load life 2000 h pn at +70 c 90 / 30 cycle 0.15 % + (0.05 ? x 100/rn) 0.5 % 0.02 % insulation resistance > 1 g ? high temperature exposure 2000 h pn at +155 c cei 68-2-20a test b 0.15 % + (0.05 ? x 100/rn) 0.10 % (duration 1000 h) 0.05 % insulation resistance > 1 g ? escc/PHR codification correspondance tables variant model case size termination 13 PHR 0402 b (tin/lead) 01 0603 02 0805 03 1206 04 2010 14 0402 g (gold) 05 0603 06 0805 07 1206 08 2010 escc/PHR codification correspondance tables temperature coefficient escc code PHR code 5 ppm/c (+22 c; +70 c) 0 z 10 ppm/c (-55 c; +155 c) 1 y 25 ppm/c (-55 c; +155 c) 2 e 5 ppm/c (-55 c; +155 c) 9 c escc/PHR codification correspondance tables tolerance escc code PHR code 0.1 % b b 0.05 % w w 0.02 % p p 0.01 % l l u = 6.25 pn x rn ??
PHR www.vishay.com vishay sfernice revision: 28-aug-15 5 document number: 53037 for technical questions, contact: sferthinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? terminations b: variants 01 / 02 / 03 / 04 and 13 ? terminations g: variants 05 / 06 / 07 / 08 and 14 notes (1) available only in size 1206. (2) plastic tape in standard for all sizes except 0402. paper tape in standard for size 0402 (option for other sizes. avai lability to be checked with factory). (3) qty. depending on size of chips. global part number information limited to 18 digits: if more digits are necessary a codification of some digits might be necessary type tcr ohmic value tolerance termination packaging option PHR0402 PHR0603 PHR0805 PHR1206 PHR2010 y = 10 ppm/c e = 25 ppm/c z = 5 ppm/c (+22 c; +70 c) c = 5 ppm/c (-55 c; +155 c) the first thre e digits are significant figures and the last digit specifies the number of zero to follow. r designates decimal point. example: 10r0 = 10 ? 3901 = 3900 ? 1004 = 1 m ? l = 0.01 % p = 0.02 % w = 0.05 % b = 0.10 % b : snpb over nickel barrier g : gold for more information see codification of packaging table leave blank if no option global part number information escc code escc spec variant ohmic value tolerance tcr 4001023 13 or 14 = 0402 01 or 05 = 0603 02 or 06 = 0805 03 or 07 = 1206 04 or 08 = 2010 the first thre e digits are significant figures and the last digit specifies the number of zero to follow. r designates decimal point. example: 10r0 = 10 ? 3901 = 3900 ? 1004 = 1 m ? l = 0.01 % p = 0.02 % w = 0.05 % b = 0.10 % 1 = 10 ppm/c 0 = 5 ppm/c (+22 c; +70 c) 2 = 25 ppm/c 9 = 5 ppm/c (-55 c; +155 c) codification packaging - waffle pack code 18 packaging w 25 min. (100 min. for size 0402), 1 mult wa 100 min., 100 mult (1) codification packaging - plastic tape (2) code 18 packaging t 50 min. (100 min. for size 0402), 1 mult ta 100 min., 100 mult tb 250 min., 250 mult tc 500 min., 500 mult td 1000 min., 1000 mult te 2500 min., 2500 mult tf full tape (3) codification packaging - paper tape (2) code 18 packaging pt 100 min., 1 mult pa 100 min., 100 mult pb 250 min., 250 mult pc 500 min., 500 mult pd 1000 min., 1000 mult pe 2500 min., 2500 mult pf full tape (3) PHR0 6 0 3y1 003bbt 4 0 1 400102301 1003b1
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
